JustMakeWeb.com รับทำเว็บไซต์ รับทำเว็บโรงแรม รับทำเว็บขายของ รับทำเว็บบริษัท เว็บสำเร็จรูป รับทำเว็บร้านค้า ออกแบบเว็บไซต์ ใช้งานได้ง่าย รองรับ SEO โปรโมท GOOGLE ให้ติดอันดับได้อย่างรวดเร็ว , ลงโฆษณาฟรี VPS ราคาถูก

มีผู้ชม 92 ครั้ง

Think Smart, as for your performance as for the environment

The unit combines conventional electrical hardware to achieve optimum operating performance at a lower cost. Running costs are much lower than compressed air driven model.

Used with an optional smart card, high savings in running cost can be realized, by delivering the paint to the user point at the correct pressure and volume only when needed.

The SMART pump range uses a standard electric motor to drive the fluid section for pumping paints, solvent and other suitable materials, reducing paint shear due to the positive dissplacement piston design and thanks to a cam and cam followers combined with a sliding carriage unit without required surge chamber.

Very recoverable against bending stress



  • Fluid Seal:
    Piston seal lubricated by paint on both sides, increasing seal life / No external paint leaks when seal requires replacement
  • Sanitary inlet and outlet connections guarantee a smooth internal pipe connection without paint entrapment pockets
  • Bellows Seal:
    no exposed shaft seal reducing the need for maintenance and lubrication of shaft packing (perfect for light & moisture sensitive materials)
  • Flow Rate Control:
    adjusted operation speed by standard AC frequency inverter to achieve a speed range from 10 to 40 cycle / min - infinite manual or automatic control
  • Reciprocating drive:
    achieved by a sliding carriage mechanism & rotating constant velocity cam with special profile reducing fluid pressure fluctuations to a minimum (no surge chamber required)
  • Operation mode:
    Simple flow mode like a conventional air motor driven pump or by pressure control to achieve maximum «Smart» energy savings
  • Horizontal Short Stroke Design:
    Equal thrust on both pistons / equal flow and pressure for both strokes / higher cycle rate than conventional vertical Pumps and thus more flexibility for paint flow range
  • Fluid sections:
    Tungsten carbide ball seats & ceramic coated pistons to maximize operating life between servicing / capability for pumping abrasive & aggressive materials


Proven Technology


  1. Low power consumption electric motor, combined with Binks Smart System, delivers significant energy savings over conventional pneumatic pumps.
  2. AC frequency inverter removes further energy loss caused by conversion to DC.
  3. New manifold elbow connections for easier configuration and installation.
  4. Universally available sanitary fittings guarantee a smooth interior connection with no paint trap pockets.
  5. New Auto-Lubrication System provides correct automatic lubrication for up to a year. Meets new ATEX requirements.
  6. Horizontal Short Stroke Design gives equal thrust from both pistons, allowing a wider cycle rate (10-40 cycles/min) and greater flexibility of flow rate.
  7. Patented reciprocating drive incorporating sliding carriage mechanism with asymmetric constant velocity cam, gives a smooth transition and virtually eliminates material pressure fluctuations.
  8. Horizontal fluid sections compatible with shear sensitive solvent and water based materials.
  9. Internal ‘Fail-safe’ bellows seal with ‘tell-tale’ leak indicator.


  E2-15 E2-30 E2-40 E2-60
Nominal stoke 50mm / 1.97" 60mm / 2.36"
Max fluid pressure 1.8 MPa 1.8 MPa 1.6 MPa 1.8 MPa
Fluid output from 20Hz to 80 Hz 3.75 L~ 15 L 7.5 L~ 30 L 10 L~ 40 L 15 L~ 60 L
Flow Volume / Cycle 0.375 L 0.75 L 1 L 1.5 L
Fluid connections Inlet and outlet 1" Sanitary Inlet and outlet 1 ½" Sanitary Inlet and outlet 1 ½" Sanitary Inlet and outlet 1 ½" Sanitary
Pump weight 78 kg 250 kg 250 kg 295 kg
Electric motor EU/USA: 400V, 3PH, 1kW
JPN: 400V, 4PH, 0.75kW
EU/USA: 400V, 3PH, 2kW
JPN: 400V, 4PH, 1.5kW
EU/USA: 400V, 3PH, 2kW
JPN: 400V, 4PH, 1.5kW
EU/USA: 400V, 3PH, 3kW
JPN: 400V, 4PH, 2.2kW



E2-15 E2-30 E2-40 E2-60
PRV22-U-10 - Pressure relief valve- 1" Sanitary PRV22-U-15 – 1 1/2" Sanitary Pressure Relief Valve 5PRV22-U-15 – 1 1/2" Sanitary Pressure Relief Valve
192547 Pressure Transducer (0 ~ 4.0 MPa)
502144 Pressure switch range (2 ~ 4.0 MPa)
192720 Sensor Manifold
502501 BPR Control Box
192206 1" Sanitary Gasket 192208 1-1/2Sanitary Gasket
192209 1" Sanitary Clamp 192209 1-1/2" Sanitary Clamp



Small footprint vertical pump


Nominal stoke 50mm / 1.97"
Maximum fluid pressure 2.0 MPa
Fluid output from 20Hz to 80 Hz 7.5L~ 30L
Flow Volume / Cycle 0.75L
Fluid connections Inlet and outlet 1 ½" Sanitary
Pump weight 256 kg
Electric motor EU: 400V, 3PH, 1.5kW




Download ►